![]() For more detailed information on the difference and different types of Y splitter cables, read our blog Y or Y Not. Unlike Y cables, stereo breakouts tend to have different colors somewhere on the connector to differentiate between the left and right outputs. While a stereo breakout will actually split a stereo signal. Despite how they look, a Y splitter cable is a general term for a variety of adapter cables, including the Y cables found on this page. These two are commonly confused for one another, and one can understand since they look the same. A stereo breakout is only one type of Y splitter designed to split a stereo signal from one connector to two independent connectors carrying each side. As already stated, a Y splitter cable or adapter refers only to the category of cables consisting of a total of three connector ends. There is a lot of confusion around these ubiquitous Y’s. All of these configurations can be found with each end being either male or female. There are other times you may need to mix connection types, such as the Hosa YPR-124 going from a ¼” TS end to dual RCA. This allows you to use an existing ¼” TRS cable with male ends. ![]() The Hosa YPP-118 is functionally the same, however it goes from a single ¼” TRS male end to two ¼” TRS female ends. You may need a “male” to “male” connection sometimes, but other times a “male” to “female” connection.Ī good example would be the Hosa CYS-103, which goes from a single ¼” TRS male end to two ¼” TRS male ends. Sometimes it is as simple as going from the same connector type to another, but it’s not always that simple. The most common audio connector types are XLR, ¼” TRS, ¼” TS, 3.5mm, and RCA. And each of these can be found with multiple connector variations. There are three basic types of Y splitter cables: Y cables, stereo breakouts, and insert cables. In the case of wanting to plug in 2 sets of headphones from a single laptop headphone jack, you’d need a Y cable with one 3.5mm TRS male end and two 3.5mm TRS female outputs to plug each headphone into, such as the YMM-232. Next, find the correct connector type for your output, typically ¼”, 3.5mm, or XLR, and determine the connector type you need for wherever it’s going. When using Y splitter cables or Y adapter cables, begin by identifying the function you require from the splitter. It’s also common for sharing headphones from a single device that has a single output, like a laptop computer or tablet. This may be needed if you want to send a duplicate output to two different sets of speakers. By duplicating that signal with a Y cable, you create an additional output. Sometimes your equipment only provides a single output to work with, or perhaps you require more outputs than your equipment allows. Y splitter cables are lifesavers in the audio world. If you are looking for stereo breakouts, you can find them here. Both of these are types of Y splitter cables but perform very different tasks.Īll Y splitter cables found on this page are Hosa Y cables. Be mindful that the use of “splitter” can be deceiving since a Y cable will duplicate the signal from the single connector end, while a stereo breakout will split a single balanced signal into two unbalanced outputs. Tour Grade Neutrik NP3X Silver 1/4" TRS JackĢx) Tour Grade Neutrik NP2X Silver 1/4" Mono Jacks.A “Y Splitter” is a common term used for any cable that has a single connector on one end, and a dual connector on the other. We sell these leads in a variety of combinations please see in store for the full selection. The cable is wired with the ‘ring’ of the Jack going to the ‘right’ mono Jack that is marked red. Black Lion Audio Bluey-500 mono compressor modified Blue Stripe compressor. ![]() The transparency and depth of sound that you get with the Sommer Onyx 2025 Twin cable and the durability of the connectors make for an excellent lead. The Neutrik Jacks are an industry standard product whose reputation speaks for itself, the cable retention inside these jacks is a unique ‘Chuck Type’ that ratchets itself onto the cable. So making it the ideal solution for ‘Insert leads’, ‘Stereo Guitar Leads’ and ‘Splitter Leads’. This is a High quality signal lead that will connect any device with a Stereo (TRS) jack output that needs to be split into two independent mono/unbalanced signals, Left/Right, Send/Return, Tip/Ring.
0 Comments
Leave a Reply. |